Operating Recommendations: Blast Models

Top of page

Do not run the engine at extremely high RPM with clutch disengaged or transmission in neutral. Running an engine at high RPM can result in engine damage. (00177a)

• The maximum recommended safe engine speed is 6500 RPM.
• Do not idle engine unnecessarily for more than a few minutes with motorcycle standing still.

Air-cooled engines require air movement over the cylinders and heads to maintain proper operating temperature. Extended periods of idling or parade duty can overheat the engine, resulting in serious engine damage. (00178a)

An engine running long distances at high speed must be given closer than ordinary attention to avoid overheating and possible damage.

When riding on wet roads, brake efficiency and traction are greatly reduced. Failure to use care when braking, accelerating or turning on wet roads can cause loss of control, which could result in death or serious injury. (00041a)

When descending upon a long, steep grade, downshift and use engine compression together with intermittent application of both brakes to slow the motorcycle.

Continuous use of brake causes overheating and reduced efficiency, which could result in death or serious injury. (00042a)

Do not coast for long distances with the engine off. The transmission is properly lubricated only when the engine is running. Coasting long distances can result in transmission damage. (00180a)

Do not tow a disabled motorcycle. Towing can adversely affect stability and handling, which could result in death or serious injury. (00017a)

Break-in Riding Rules: Blast Models

Top of page

The First 500 Miles (800 Kilometers)

The sound design, quality materials and workmanship built into your new Buell motorcycle will give you optimum performance right from the start.

So that your engine can wear in its critical parts, we recommend that for the first 500 miles (800 kilometers) you observe the simple riding rules below. Adherence to these suggestions will help to assure good future durability and performance.

1. During the first 50 miles (80 kilometers), keep the engine speed below 4000 RPM in any gear. Do not lug the engine by running or accelerating at very low RPM, or stay at high RPM longer than needed for shifting or passing.

2. Up to 500 miles (800 kilometers), vary the engine speed and avoid operating at any steady engine speed for long periods. Engine speeds up to 5000 RPM are permissible in any gear.

3. Drive slowly and avoid fast starts at wide open throttle until the engine warms up.

4. Avoid lugging the engine by not running the engine at very low speeds in higher gears.

Pre-Riding Checklist: Buell Models

Top of page

Read the CONTROLS AND INDICATORS section before riding your motorcycle. Failure to understand the operation of the motorcycle could result in death or serious injury. (00043a)

Before riding your motorcycle at any time, make a general inspection to be sure it is in safe riding condition.

Stop the engine when refueling or servicing the fuel system. Do not smoke or allow open flame or sparks near gasoline. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00002a)

Avoid spills. Slowly remove filler cap. Do not fill above bottom of filler neck insert, leaving air space for fuel expansion. Secure filler cap after refueling. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00028a)

Use care when refueling. Pressurized air in fuel tank can force gasoline to escape through filler tube. Gasoline is extremely flammable and highly explosive, which could result in death or serious injury. (00029a)

Do not spill fuel onto the motorcycle while refueling. Immediately wipe up fuel spills on your motorcycle. Fuel can cause damage to cosmetic surfaces. (00147b)

1. Verify fuel is present in tank and add fuel if required.

2. Adjust mirrors to proper riding positions.

3. Verify oil is present in oil tank. Check oil level only after warming up the motorcycle.

4. Check controls to make sure they operate properly. Operate the front and rear brakes, throttle, clutch and shifter. All controls should operate freely without binding.

5. Check steering for proper operation by turning the handlebars through the full operating range. Handlebars should turn smoothly without binding.

Be sure tires are properly inflated, balanced and have adequate tread. Inspect your tires regularly and see a Buell dealer for replacements. Riding with excessively worn, unbalanced or under-inflated tires can adversely affect stability and handling, which could result in death or serious injury. (00114a)

6. Check tire condition and pressure. Incorrect pressure will result in poor riding characteristics and can affect handling and stability.

7. Check all electrical equipment and switches including the headlamp, stop lamp, turn signals and horn, for proper operation.

NOTE:


Check horn operation with engine running.

Be sure headlamp, tail and stop lamp and turn signals are operating properly before riding. Poor visibility of rider to other motorists can result in death or serious injury. (00478b)

8. Check for any fuel, oil or hydraulic fluid leaks.

9. Check secondary belt for wear or damage. Service as necessary.

Starting The Engine: Blast Models

Top of page

Shift transmission to neutral before starting engine to prevent accidental movement, which could result in death or serious injury. (00044a)

FINE-C Method

Before starting the engine perform the pre-ride inspection and then complete the following steps:

1. FUEL: Check that the fuel supply valve handle is to the ON position. The fuel supply valve handle is located on the left side under the fuel tank. See Fuel Supply Valve Operation: Blast Models.

2. IGNITION: Insert the key in the ignition/headlamp key switch and turn the key clockwise to the IGNITION position. See Ignition/Headlamp Key Switch: Blast Models.

3. NEUTRAL: Make sure transmission is in neutral. Check to see if green neutral indicator lamp is illuminated. Roll motorcycle forwards and backwards to verify transmission is in neutral. See Indicator Lamps: Blast Models.

4. ELECTRIC STARTER: Push the bottom of the engine off/run switch to the RUN position. The engine off/run switch is located on the right handlebar control. See Handlebar Controls: Blast Models.

5. CLUTCH: Squeeze the clutch lever (1) in. The clutch lever is located just forward of the left handlebar grip. See Handlebar Controls: Blast Models.

6. Retract the sidestand.

7. Push the electric starter switch (10) to start the engine. The electric starter switch is located on the right handlebar control. See Handlebar Controls: Blast Models.

If you have any questions about the correct operation of your motorcycle, talk to an authorized Buell dealer.

Stopping the Engine: Blast Models

Top of page

1. See Handlebar Controls: Blast Models. Push the upper part of the engine off/run switch to shut the engine OFF. The engine off/run switch is located on the right handlebar control.

2. See Ignition/Headlamp Key Switch: Blast Models. Turn the ignition/headlamp key switch counterclockwise to the OFF position.

3. See Fuel Supply Valve Operation: Blast Models. Turn the fuel supply valve handle OFF.

Shifting Gears

Top of page

Getting Started

The clutch must be fully disengaged before attempting a gear shift. Failure to fully disengage the clutch can result in equipment damage. (00182a)

Gear shift pattern is first gear down, next four gears up.

1. With motorcycle engine running and sidestand retracted, pull the clutch hand lever in against handlebar grip to fully disengage clutch.

2. Push the foot shift lever down to end of its travel and release. The transmission is now in first gear.

3. To start forward motion, release the clutch lever slowly to engage the clutch and at the same time, open throttle gradually.

Upshift (Acceleration)

Refer to Upshift (Acceleration) Gear Speeds: 2007 Blast Models. Engage second gear after the motorcycle has reached the appropriate shifting speed.

Upshift (Acceleration) Gear Speeds: 2007 Blast Models

1. Close the throttle.

2. Disengage the clutch (pull clutch lever in).

3. See Shifting Sequence: Upshift. Lift the gear shift lever up to the end of its travel and release.

4. Engage the clutch (release clutch lever) and gradually open the throttle.

5. Repeat the previous steps to engage third, fourth, and fifth gears.

Shifting Sequence: Upshift

Downshift (Deceleration)

Do not downshift at speeds higher than those listed in the Changing Gear Speeds table. Shifting to lower gears when speed is too high can cause the rear wheel to lose traction and lead to loss of vehicle control, which could result in death or serious injury. (00045a)

Gear shift pattern is fourth gear down; next three gears down. Refer to Downshift (Deceleration) Gear Speeds: 2007 Blast Models for shifting speeds.

Downshift (Deceleration) Gear Speeds: 2007 Blast Models

See Shifting Sequence: Downshift. When engine speed decreases, as in climbing a hill or running at a reduced speed, shift to the next lower gear while partially closing the throttle so the engine accelerates as soon as the clutch lever is released.

Shift to neutral before stopping engine. Shifting mechanism can be damaged by shifting gears while engine is stopped. (00183a)

The gear shifter mechanism permits shifting the transmission to neutral from either first or second gear.

Shifting Sequence: Downshift